← Back to the MTX FORGE card · All how-to pages
How to use
MTX FORGE
NoiZee ToyZ pack · coming soon to VCV
What it does
MTX FORGE is MTX-8 and the whole GRAIN-FORGE effects chain in one panel. An 8x8 pad grid plays eight built-in synth voices (one per row) with accents and eight patterns, and the touch strips shape every voice live in eight banks.
The voice mix, plus anything you patch into IN L / IN R, runs through FORGE FX: SHUFFLE, GLITCH, ROBOT, PULSE and WARP DLY, then a master filter with its own envelope. Everything is clocked by the sequencer, so the effects stay in time with the groove. It runs at 120 BPM with nothing in CLK.
Quick start
- Patch OUT L and OUT R (bottom right) to your mixer or audio out.
- Press RAND (over the jacks beside the grid) for grooves on all eight patterns, in key. Or click pads to set steps: each row is a voice, each column a step.
- Make sure RUN is lit (green). With nothing in CLK it plays at 120 BPM; patch a 16th-note clock to set your own tempo.
- Click the FX names on the screen in the middle (SHUFFLE, GLITCH ...) to switch stages on and off, then bring them in with DRY / WET.
- Or click the PRESET line and pick a ready-made chain, such as DUB ECHO or TRANCE GATE.
Controls
Grid and patterns
- Pads: click to set or clear a step. Right-click a pad to make it an accent (louder); right-click again for a plain hit.
- 1-8 (the buttons over the grid): pick the pattern. Each pattern keeps its own steps and accents.
- RAND: new grooves on all eight patterns (a theme and variations over a chord progression, in key, accents on the downbeats) and new values on every strip bank. Ctrl+Z takes it back.
- CLEAR: empties the current pattern. Clear every pattern is in the right-click menu.
- LOOP column: ▲ / ▼ step the pattern length (1-8), and the bar shows the looped steps and the playhead (click a cell to loop up to it).
- RUN and RESET: start / stop and back to step 1. A trigger at the RUN or RST jack does the same.
Touch strips
- A-H: pick the bank: A PITCH, B CUTOFF, C RESO, D DECAY, E WAVE, F LEVEL, G PAN, H DRIVE. Each strip is one voice.
- Strips: drag (or click) to set that voice's value. Its voltage also comes out of the jack above it.
- ±5V: lit = the strip jacks send -5..+5 V; off = 0..10 V.
Voice sound
- CUTOFF, RES, ENV, MODE: a second filter on every voice; MODE morphs low-pass to band-pass to high-pass.
- ATK, DEC, SUS, REL: the envelope for all eight voices.
- DELAY (a ping-pong dotted eighth) and SPACE (reverb) on the voices, before FORGE FX.
- MASTER: output volume. Its voltage comes out of KNOB (0-10 V).
FORGE FX
On the screen, click a stage's name to switch it on, and click or scroll its value to step it (right-click steps back). Each stage's RND makes it pick new musical settings every cycle. The six small knobs under the screen, one row per stage, set it by hand.
- SHUFFLE: moves, reverses and octave-shifts slices of the beat (PATTERN, AMOUNT, REVERSE, OCTAVE, LENGTH, MIX).
- GLITCH: random rolls, reverses, tape-stops and crush on the steps (CHANCE, ROLL, REVERSE, STOP, CRUSH, MIX). A trigger at GLITCH fires one now.
- ROBOT: a robot vocoder tuned to a root and chord (ROOT, CHORD, VOWEL, RING, RES, MIX).
- PULSE: a rhythmic gate and filter sweep (CUTOFF, RES, DEPTH, PATTERN, DECAY, MIX, and LP / BP / HP on the screen). A gate at OPEN lets everything through while high.
- WARP DLY: a clocked delay whose repeats shift in pitch and can run back through ROBOT and PULSE (TIME, FDBK, WARP, ROUTE, TONE, ECHO).
- THROW: the 16 cells send just those steps into the delay; its RND rolls a new throw pattern.
- PRESET: click to step through ready-made chains, right-click for the list. CYCLE sets how often RND picks (1 beat to 8 bars), GLIDE how fast knobs travel there, FREEZE holds the current picks.
- TRIG and the bar screen: what fires the master filter's envelope (BEAT, STEP, PULSE, GLITCH, SEQ or GATE). On SEQ, click a bar to switch that step, drag across bars to paint their heights. BYP takes the envelope off the filter. A gate at GATE fires it when TRIG is GATE.
- FILTER, RES, ENV, AMP, ATK / DEC / SUS / REL: the master filter, its envelope depth, how much the envelope also shapes the level, and the envelope. 1 / 2 / 3 stages (12-36 dB) and LP / BP / HP are on the screen.
- INPUT, DRY / WET, OUTPUT: level into the FX, the blend, and the level out.
Controller
- MIDI IN / MIDI OUT (the top screen): click a line to pick the port. MIDI beside them: green = FORGE listens to the JAM; off = it ignores it and its lights go dark.
- LEARN: arm it, then press the top-left pad on the JAM so FORGE knows which pad page it is on.
- Right-click menu: Controller (Auto, Maschine JAM, or APC mini mk2, Launchpad Mini MK3, Launchpad X, Launchpad Pro MK3 in beta), RAND genre (RANDROYD's chords: AUTO follows a RANDROYD in the rack), pattern length, JAM matrix page, strip bank, Clear every pattern and the JAM light colours.
- On a Maschine JAM: hold MUTE or SOLO and press a pad to mute or solo that voice; hold CLEAR for a second to clear every pattern; PLAY starts and stops FORGE (or the song when an MTX Composer is in the patch). The JAM knob sets MASTER (MST / CUE), DELAY (GRP) or SPACE (IN1).
Jacks
Inputs
- Left added to the voices before the FX; patch SynTHBloK DUO here
- Right left is copied here when unpatched
- Clock 16th notes; steps the sequencer and the FX; 120 BPM internal when unpatched
- Reset trigger: same as pressing RESET
- Run trigger: toggles RUN, like pressing it
Outputs
- Track N trigger
- Strip N
- Knob 0..10 V
- Audio left
- Audio right
N = 1, 2, 3 ... (one jack per track, channel or strip). Hover a jack in Rack for the same text.
Tips
- Pairs well with MTX-8 (its free little brother): patch MTX-DUO into IN L / IN R so its lead and bass run through the same FX, add MTX-DRUM, then MORPH for big knob moves.
- Every row has its own trigger out (the jacks beside the grid), so a row can also play an outside drum or envelope.
- Light RND on one or two stages only (GLITCH and WARP DLY are a good start) and set CYCLE to 4 or 8 bars: the FX keep changing without burying the groove.
- Click a few THROW cells to drop single steps into the warp delay for dub-style throws.